Construction of double reaction zones for long-life quasi-solid aluminum-ion batteries by realizing maximum electron transfer.

Achieving high energy density and long cycling life simultaneously remains the most critical challenge for aluminum-ion batteries (AIBs), especially for high-capacity conversion-type positive electrodes suffering from shuttle effect in strongly acidic electrolytes. Herein, we develop a layered quasi-solid AIBs system with double reaction zones (DRZs, Zone 1 and Zone 2) to address such issues. Zone 1 is designed to accelerate reaction kinetics by improving wetting ability of quasi-solid electrolyte to active materials. A composite three-dimensional conductive framework (Zone 2) interwoven by gel network for ion conduction and carbon nanotube network as electronic conductor, can fix the active materials dissolved from Zone 1 to allow for continuing electrochemical reactions. Therefore, a maximum electron transfer is realized for the conversion-type mateials in DRZs, and an ultrahigh capacity (400 mAh g-1) and an ultralong cycling life (4000 cycles) are achieved. Such strategy provides a new perspective for constructing high-energy-density and long-life AIBs.

Improved salt-tolerance of transgenic soybean by stable over-expression of AhBADH gene from Atriplex hortensis.

KEY MESSAGE: The salt-tolerance of transgenic soybean cleared for environmental release was improved by stable over-expression of AhBADH gene from Atriplex hortensis, which was demonstrated through molecular analysis and field experiments. An effective strategy for increasing the productivity of major crops under salt stress conditions is the development of transgenics that harbor genes responsible for salinity tolerance. Betaine aldehyde dehydrogenase (BADH) is a key enzyme involved in the biosynthesis of the osmoprotectant, glycine betaine (GB), and osmotic balance in plants, and several plants transformed with BADH gene have shown significant improvements in salt tolerance. However, very few field-tested transgenic cultivars have been reported, as most of the transgenic studies are limited to laboratory or green house experiments. In this study, we demonstrated through field experiments that AhBADH from Atriplex hortensis confers salt tolerance when transformed into soybean (Glycine max L.). AhBADH was successfully introduced into soybean by Agrobacterium mediated transformation. A total of 256 transgenic plants were obtained, out of which 47 lines showed significant enhancement of salt tolerance compared to non-transgenic control plants. Molecular analyses of the transgenic line TL2 and TL7 with the highest salt tolerance exhibited stable inheritance and expression of AhBADH in progenies with a single copy insertion. TL1, TL2 and TL7 exhibited stable enhanced salt tolerance and improved agronomic traits when subjected to 300mM NaCl treatment. Currently, the transgenic line TL2 and TL7 with stable enhanced salt tolerance, which have been cleared for environmental release, are under biosafety assessment. TL 2 and TL7 stably expressing AhBADH could then be applied in commercial breeding experiments to genetically improve salt tolerance in soybean.

Comparative transcriptome analysis of Veratrum maackii and Veratrum nigrum reveals multiple candidate genes involved in steroidal alkaloid biosynthesis.

Veratrum (Melanthiaceae; Liliales) is a genus of perennial herbs known for the production of unique bioactive steroidal alkaloids. However, the biosynthesis of these compounds is incompletely understood because many of the downstream enzymatic steps have yet to be resolved. RNA-Seq is a powerful method that can be used to identify candidate genes involved in metabolic pathways by comparing the transcriptomes of metabolically active tissues to controls lacking the pathway of interest. The root and leaf transcriptomes of wild Veratrum maackii and Veratrum nigrum plants were sequenced and 437,820 clean reads were assembled into 203,912 unigenes, 47.67% of which were annotated. We identified 235 differentially expressed unigenes potentially involved in the synthesis of steroidal alkaloids. Twenty unigenes, including new candidate cytochrome P450 monooxygenases and transcription factors, were selected for validation by quantitative real-time PCR. Most candidate genes were expressed at higher levels in roots than leaves but showed a consistent profile across both species. Among the 20 unigenes putatively involved in the synthesis of steroidal alkaloids, 14 were already known. We identified three new CYP450 candidates (CYP76A2, CYP76B6 and CYP76AH1) and three new transcription factor candidates (ERF1A, bHLH13 and bHLH66). We propose that ERF1A, CYP90G1-1 and CYP76AH1 are specifically involved in the key steps of steroidal alkaloid biosynthesis in V. maackii roots. Our data represent the first cross-species analysis of steroidal alkaloid biosynthesis in the genus Veratrum and indicate that the metabolic properties of V. maackii and V. nigrum are broadly conserved despite their distinct alkaloid profiles.

Selection principles of polymeric frameworks for solid-state electrolytes of non-aqueous aluminum-ion batteries.

Liquid electrolyte systems of aluminum-ion batteries (AIBs) have restrictive issues, such as high moisture sensitivity, strong corrosiveness, and battery leakage, so researchers have turned their attention to developing high safety, leak-free polymer electrolytes. However, the stability of the active factor of AIB systems is difficult to maintain with most of polymeric frameworks due to the special Al complex ion balance in chloroaluminate salts. Based on this, this work clarified the feasibility and specific mechanism of using polymers containing functional groups with lone pair electrons as frameworks of solid-state electrolytes for AIBs. As for the polymers reacting unfavorably with AlCl3, they cannot be used as the frameworks directly due to the decrease or even disappearance of chloroaluminate complex ions. In contrast, a class of polymers represented by polyacrylamide (PAM) can interact with AlCl3 and provide ligands, which not only have no effect on the activity of Al species but also provide chloroaluminate complex ions through complexation reactions. According to DFT calculations, amide groups tend to coordinates with AlCl2 + via O atoms to form [AlCl2(AM)2]+ cations, while disassociating chloroaluminate anions. Furthermore, the PAM-based solid-state and quasi-solid-state gel polymer electrolytes were also prepared to investigate their electrochemical properties. This work is expected to provide new theoretical and practical directions for the further development of polymer electrolytes for AIBs.

Full space coordinate measurement method with a portable light pen by using hybrid light field imaging.

The light pen is one of the most useful spatial coordinate measurement methods. However, due to the principle of vision measurement, the traditional light pen has the disadvantages such as limited measurement range, large structure size and complex calibration process. In order to revolutionize the design of light pen, this paper proposes a full space coordinate measurement method with a portable light pen by using hybrid light field imaging. Firstly, a light field imaging system with depth estimation ability has been introduced to simplify the light pen structure to three target points by using P3P method. In order to improve the accuracy of the depth estimation, a hybrid imaging method and EPI method have been used. Secondly, a full spatial measurement method with a rotation platform has been presented in detail. Finally, the experiments have been designed to verify the effectiveness and accuracy of the proposed method.

Nonaqueous Rechargeable Aluminum Batteries: Progresses, Challenges, and Perspectives.

For significantly increasing the energy densities to satisfy the growing demands, new battery materials and electrochemical chemistry beyond conventional rocking-chair based Li-ion batteries should be developed urgently. Rechargeable aluminum batteries (RABs) with the features of low cost, high safety, easy fabrication, environmental friendliness, and long cycling life have gained increasing attention. Although there are pronounced advantages of utilizing earth-abundant Al metals as negative electrodes for high energy density, such RAB technologies are still in the preliminary stage and considerable efforts will be made to further promote the fundamental and practical issues. For providing a full scope in this review, we summarize the development history of Al batteries and analyze the thermodynamics and electrode kinetics of nonaqueous RABs. The progresses on the cutting-edge of the nonaqueous RABs as well as the advanced characterizations and simulation technologies for understanding the mechanism are discussed. Furthermore, major challenges of the critical battery components and the corresponding feasible strategies toward addressing these issues are proposed, aiming to guide for promoting electrochemical performance (high voltage, high capacity, large rate capability, and long cycling life) and safety of RABs. Finally, the perspectives for the possible future efforts in this field are analyzed to thrust the progresses of the state-of-the-art RABs, with expectation of bridging the gap between laboratory exploration and practical applications.

Rechargeable Nickel Telluride/Aluminum Batteries with High Capacity and Enhanced Cycling Performance.

Rechargeable aluminum-ion batteries (AIBs) possess significant advantages of high energy density, safety performance, and abundant natural resources, making them one of the desirable next-generation substitutes for lithium battery systems. However, the poor reversibility, short lifespan, and low capacity of positive materials have limited its practical applications. In comparison with semiconductors, the metallic nickel telluride (NiTe) alloy with enhanced electrical conductivity and fast electron transmission is a more favorable electrode material that could significantly decrease the kinetic barrier during battery operation for energy storage. In this paper, the NiTe nanorods prepared through a simple hydrothermal routine enable an initial reversible capacity of approximately 570 mA h g-1 (under the current density of 200 mA g-1) to be delivered on the basis of the ionic liquid electrolyte, along with the average voltage platform of about 1.30 V. Moreover, the cycling performance could be easily enhanced using a modified separator to prevent the diffusion of soluble intermediate species to the negative electrode side. At a high rate of 500 mA g-1, the NiTe nanorods could retain a specific capacity of about 307 mA h g-1 at the 100th cycle. The results have important implications for the research of transition metal tellurides as positive electrode materials for AIBs.

Agrobacterium-Mediated Genetic Transformation of the Medicinal Plant Veratrum dahuricum.

Veratrum dahuricum L. (Liliaceae), a monocotyledonous species distributed throughout the Changbai mountains of Northeast China, is pharmaceutically important, due to the capacity to produce the anticancer drug cyclopamine. An efficient transformation system of Veratrum dahuricum mediated with Agrobacterium tumefaciens is presented. Murashige and Skoog (MS) medium containing 8 mg/L picloram was used to induce embryogenic calli from immature embryos with 56% efficiency. A. tumefaciens LBA4404 carrying the bar gene driven by the cauliflower mosaic virus 35S promoter was employed for embryogenic callus inoculation. A. tumefaciens cell density OD660 = 0.8 for inoculation, half an hour infection period, and three days of co-culture duration were found to be optimal for callus transformation. Phosphinothricin (PPT, 16 mg/L) was used as the selectable agent, and a transformation efficiency of 15% (transgenic plants/100 infected calli) was obtained. The transgenic nature of the regenerated plants was confirmed by PCR and Southern blot analysis, and expression of the bar gene was detected by RT-PCR and Quick PAT/bar strips. The steroid alkaloids cyclopamine, jervine, and veratramine were detected in transgenic plants, in non-transformed and control plants collected from natural sites. The transformation system constitutes a prerequisite for the production of the pharmaceutically important anticancer drug cyclopamine by metabolic engineering of Veratrum.

Image distortion correction method in a nonuniform temperature field by using Runge-Kutta ray tracing.

To solve the imaging distortion problem in a nonuniform temperature field for visual measurement, this paper studies the Runge-Kutta ray tracing algorithm. First, the light ray emitted by the spatial light point will be abstracted by the proposed method. Then, the ray trajectory in a 3D nonuniform temperature gradient environment will be reproduced, and the ray distortion can be corrected. Finally, the distortion is compared with the actual image distortion obtained through the corner detection method. The experimental results show that the correction method for the distortion image caused by nonuniform temperature gradient heat source interference is feasible by using the Runge-Kutta ray tracing algorithm, which can realize the error compensation for image distortion and obtain an accurate corrected image.

Dynamic Changes in Metabolite Accumulation and the Transcriptome during Leaf Growth and Development in Eucommia ulmoides.

Eucommia ulmoides Oliver is widely distributed in China. This species has been used mainly in medicine due to the high concentration of chlorogenic acid (CGA), flavonoids, lignans, and other compounds in the leaves and barks. However, the categories of metabolites, dynamic changes in metabolite accumulation and overall molecular mechanisms involved in metabolite biosynthesis during E. ulmoides leaf growth and development remain unknown. Here, a total of 515 analytes, including 127 flavonoids, 46 organic acids, 44 amino acid derivatives, 9 phenolamides, and 16 vitamins, were identified from four E. ulmoides samples using ultraperformance liquid chromatography-mass spectrometry (UPLC-MS) (for widely targeted metabolites). The accumulation of most flavonoids peaked in growing leaves, followed by old leaves. UPLC-MS analysis indicated that CGA accumulation increased steadily to a high concentration during leaf growth and development, and rutin showed a high accumulation level in leaf buds and growing leaves. Based on single-molecule long-read sequencing technology, 69,020 transcripts and 2880 novel loci were identified in E. ulmoides. Expression analysis indicated that isoforms in the flavonoid biosynthetic pathway and flavonoid metabolic pathway were highly expressed in growing leaves and old leaves. Co-expression network analysis suggested a potential direct link between the flavonoid and phenylpropanoid biosynthetic pathways via the regulation of transcription factors, including MYB (v-myb avian myeloblastosis viral oncogene homolog) and bHLH (basic/helix-loop-helix). Our study predicts dynamic metabolic models during leaf growth and development and will support further molecular biological studies of metabolite biosynthesis in E. ulmoides. In addition, our results significantly improve the annotation of the E. ulmoides genome.

Facile synthesis of Ni11(HPO3)8(OH)6/rGO nanorods with enhanced electrochemical performance for aluminum-ion batteries.

The electrochemical behaviors of the ultrashort nickel phosphite nanorods supported on reduced graphene oxide (Ni11(HPO3)8(OH)6/rGO nanorods), as a candidate for cathodic applications in aluminum-ion batteries, are firstly investigated. Ni11(HPO3)8(OH)6/rGO nanorods are synthesized by a facile solvothermal process. Ni11(HPO3)8(OH)6 and Ni11(HPO3)8(OH)6/rGO cathodes both possess very high initial discharge capacities of 132.4 and 182.0 mA h g-1 at a current density of 200 mA g-1, respectively. In addition, the long-term cycling stability of the Ni11(HPO3)8(OH)6/rGO cathode is further evaluated, exhibiting a discharge capacity of 49.2 mA h g-1 even over 1500 cycles. More importantly, the redox reaction mechanism of the Ni11(HPO3)8(OH)6 cathode for aluminum-ion batteries revealed that Ni11(HPO3)8(OH)6 is partially substituted with Al3+ to form AlmNin(HPO3)8(OH)6 and metallic Ni in the nanorod-like Ni11(HPO3)8(OH)6 cathodes during the discharge process. These findings are of great significance for the further development of novel materials for aluminum-ion batteries.

Ordered WO3-x nanorods: facile synthesis and their electrochemical properties for aluminum-ion batteries.

In this work, we have synthesized ordered WO3 nanorods via a facile hydrothermal process. And the series WO3-x nanorods with oxygen vacancies are obtained via a subsequent thermal reduction process. The formation mechanisms of WO3-x nanorods with different oxygen vacancies are proposed. And the electrochemical results reveal that the WO3-x nanorods exhibit the improved specific capacity due to the oxygen vacancies caused by the thermal reduction. More importantly, the reaction mechanism of the WO3-x nanorods as cathodes for aluminum-ion batteries has been proved.

Airplane wing deformation and flight flutter detection method by using three-dimensional speckle image correlation technology.

Airplane wing deformation is an important element of aerodynamic characteristics, structure design, and fatigue analysis for aircraft manufacturing, as well as a main test content of certification regarding flutter for airplanes. This paper presents a novel real-time detection method for wing deformation and flight flutter detection by using three-dimensional speckle image correlation technology. Speckle patterns whose positions are determined through the vibration characteristic of the aircraft are coated on the wing; then the speckle patterns are imaged by CCD cameras which are mounted inside the aircraft cabin. In order to reduce the computation, a matching technique based on Geodetic Systems Incorporated coded points combined with the classical epipolar constraint is proposed, and a displacement vector map for the aircraft wing can be obtained through comparing the coordinates of speckle points before and after deformation. Finally, verification experiments containing static and dynamic tests by using an aircraft wing model demonstrate the accuracy and effectiveness of the proposed method.

Exfoliation Mechanism of Graphite Cathode in Ionic Liquids.

Graphene has been successfully electrochemically exfoliated by electrolysis of cathode graphite in the aluminum-ion battery with ionic liquid electrolyte comprising AlCl3 and 1-ethyl-3-methylimidazolium chloride ([EMIm]Cl). The AlCl4-, Al2Cl7-, etc., intercalation into graphite flakes in ionic liquid of the aluminum-ion battery by different electrolysis processes to exfoliate graphite has been researched in detail. As a result of the enhanced structural flexibility, the intercalant gallery height increases in the less than five-layer graphene film, providing more free space for AlCl4-, Al2Cl7-, etc. transport. Therefore, a quantity of 3-5 layers rather than 1-2 layers of graphene can be obtained. The results clearly demonstrate that graphene has been produced in the graphite cathode in AlCl3/EMImCl ionic liquids, which is significantly meaningful for accelerating the theoretical research and industrialized application of graphene. Meanwhile, it has a vitally important role for promoting the recycling Al-ion batteries.

A total station spatial positioning method based on rotary laser scanning and ultrasonic ranging.

Total station spatial coordinator measuring technology is extensively applied in the large-scale measurement of industrial assembly and manufacturing for its flexibility and adaptability. The existing total station technology has some principal limits such as poor efficiency and single tasking; in order to achieve the total station spatial coordinator measuring technology with the advantages of multi-task, real-time measurement, and high accuracy, this paper presents a novel total station measurement method by using multi-laser plane constraints established through rotating planar planes and distance information obtained with an ultrasonic ranging method. With the spatial divergence angles of the optoelectronic scanning and ultrasonic arrays, this method can measure the spatial coordinates in multi-task and real-time with a single station and a portable target bar. Experimental results show that the proposed method is feasible and valid with satisfactory accuracy. The maximum distance measurement error is less than 0.2 mm in a volume that is 5 m far away from the station.

Hexagonal NiS nanobelts as advanced cathode materials for rechargeable Al-ion batteries.

Hexagonal NiS nanobelts served as novel cathode materials for rechargeable Al-ion batteries based on an AlCl3/[EMIm]Cl ionic liquid electrolyte system. The nano-banded structure of the materials can facilitate the electrolyte immersion and enhance Al(3+) diffusion. The hexagonal NiS nanobelt based cathodes exhibit high storage capacity, good cyclability and low overpotential.

Self-calibration method for rotating laser positioning system using interscanning technology and ultrasonic ranging.

A rotating laser positioning system (RLPS) is an efficient measurement method for large-scale metrology. Due to multiple transmitter stations, which consist of a measurement network, the position relationship of these stations must be first calibrated. However, with such auxiliary devices such as a laser tracker, scale bar, and complex calibration process, the traditional calibration methods greatly reduce the measurement efficiency. This paper proposes a self-calibration method for RLPS, which can automatically obtain the position relationship. The method is implemented through interscanning technology by using a calibration bar mounted on the transmitter station. Each bar is composed of three RLPS receivers and one ultrasonic sensor whose coordinates are known in advance. The calibration algorithm is mainly based on multiplane and distance constraints and is introduced in detail through a two-station mathematical model. The repeated experiments demonstrate that the coordinate measurement uncertainty of spatial points by using this method is about 0.1 mm, and the accuracy experiments show that the average coordinate measurement deviation is about 0.3 mm compared with a laser tracker. The accuracy can meet the requirements of most applications, while the calibration efficiency is significantly improved.

A new aluminium-ion battery with high voltage, high safety and low cost.

A new kind of Al-ion battery with carbon paper as the cathode, high-purity Al foil as the anode and ionic liquid as the electrolyte is proposed in this work. The significance of the presented battery is going to be an extremely high average voltage plateau of ca. 1.8 V vs. Al(3+)/Al.

[Huanglian jiedu decoction regulated and controlled differentiation of monocytes, macrophages, and foam cells: an experimental study].

OBJECTIVE: To observe the effect of Huanglian Jiedu Decoction (HLJDD) in in vivo regulating differentiation of monocytes in an apolipoprotein E knockout (ApoE(-/-)) mouse model, and to observe the effect of HLJDD-containing serum in in vitro regulating differentiation of macrophages and foam cells. METHODS: Fifteen apoE(-/-) mice were randomly divided into the common diet group, the hyperlipidemia group, and the hyperlipidemia +HLJDD treatment group, 5 in each group. Mice in the common diet group were fed with a chow diet. Mice in the hyperlipidemia group were fed with high cholesterol wild diet (WD). Those in the hyperlipidemia +HLJDD treatment group were fed with high cholesterol WD supplemented with HLJDD. All mice were fed for 4 weeks. Five C57BL/6 wild types were recruited as the wild common diet control group. HLJDD was administered to mice in the hyperlipidemia + HLJDD treatment group by gastrogavage at the daily dose of 5 g/kg. Equal volume of purified water was given by gastrogavage to mice in the rest 3 groups. Four weeks later, subtypes of monocytes in the peripheral blood were detected by FACS. HLJDD administered to another 30 SD rats by gastrogavage at the daily dose of 5 g/kg, once for every 12 h for 5 times in total, thereby preparing 5% HLJDD containing serum to intervene the differentiation of in vitro primary bone marrow-derived macrophage (BMDM) and foam cells. The M2 subtype surface receptor CD206 of macrophages and foam cells were detected by FACS. The expression of Nos2 and Arg1 genes were assayed by Real-time PCR. RESULTS: The ratio of inflammatory subset of monocytes (Ly6C(high)) increased in the peripheral blood after ApoE(-/-) mice were fed with high fat diet for 4 weeks. HLJDD significantly decreased the ratio of inflammatory subset of monocytes (P < 0.05). Compared with the vehicle serum, 5% HLJDD containing serum significantly increased differentiation of CD206 + M2 BMDM (P = 0.034). Results of real-time quantitative PCR showed that the expression level of Arg1 mRNA could be up-regulated by HLJDD containing serum (P < 0.05), and that of Nos2 mRNA down-regulated (P = 0.017). ox-LDL induced the differentiation of M2 subtype foam cells from BMDM, and HLJDD containing serum could further elevate the ratio of CD206 + M2 foam cells and increase the Arg1 mRNA expression level (both P < 0.01). HLJDD containing serum could inhibit the inversion of M2 subtype of foam cells to M1 subtype induced by Th1 factors, significantly elevate the Arg1 mRNA expression level, and decrease the Nos2 mRNA expression level (all P < 0.01). CONCLUSIONS: HLJDD could lower hyperlipidemia induced inflammatory monocyte subtype ratios in the peripheral blood of ApoE(-/-) mice. HLJDD containing serum promoted in vitro differentiation of M2 macrophages and foam cells. HLJDD attenuated and inhibited the occurrence and development of atherosclerosis induced by hyperlipidemia possibly through regulating the functional differentiation of monocytes, macrophages, and foam cells.